 | | | Oracle on SUSE Linux | | Hi Antonio
> - How can i know if management server is run
emctl status dbconsole
> - on which port is running
see output of status command
> - How can i start it
emctl start dbconsoHi
can do you help my about
- How can i know if management server is run
- on which port is running
- How can i start it
Thanks
--
To unsubscribe email suse-oracle-unsubscribe@(protected)Reidar Agas?ster wrote
> I have an update in this case
> In this file
> /etc/pam.d/su
> I added a line
> session required pam_limits.so
>
> which I think solved my problem...
>
>
I have an update in this case
In this file
/etc/pam.d/su
I added a line
session required pam_limits.so
which I think solved my problem...
If any other could confirm this soultion
Hi
Im on Suse Linux Enterprise Server 8 with Oracle 10g and orarun-1.8-11.
When I do shutdown -r now as root the console says in the shutdown section of oracle shutdown script
-su I met the same problem.
My error was to edit the wrapper with a vi instead of using the "cat "
command.
It is likely some kind of caracters didn 't permit the script to be
interpreted correctly.
I forgot to set LD_ASSUME_KERNEL for the oracle user...
-CC
--
To unsubscribe email suse-oracle-unsubscribe@(protected)
For additional commands email suse-oracle-help@(protected)
Please see
I installed 9.2.0.4 onto SuSE 9.1. I applied patch 3006854 from Metalink to get past the OUI
problems and the install seemed to proceed fine from there. However I cannot get dbca or netca to
workThanks for the suggestion but this did not solved the issue.
I managed to find that for some reason the SHMMAX values of the two machines
were set differently (i.e. too low for the one that didn 'tKevin Closson wrote
> >Andrew
> >you don 't have to use raw. You have the option to use OCFS (Oracle
> >cluster file system) or you can go for a NetApp solution for 9iRAC
> >
> >
>
>I don 'tFrom "Certify - Product Version and Other Selections RAC for Linux On
Linux x86 " on metalink.
SuSE SLES8 || 10g Oracle || OSD Clusterware 10g || Projected
So I 'd say... sadly... not yet.
Get a trace of event 1006 and you will see.
Hi
i have installed Oracle9iR2 9.0.2.3 suse 7.2
Reports Server 9.0.2.0.1
I have been experienced some problems with reports server
it hangs continuosly when runnig simple and complex reports.
Hi Andrew
will you use 2 x455 with each 4 CPU or 1 x455 with 8 CPU?
Yours
Ralf
> > > "Kevin Closson " <kevinc@(protected) > 14.09.2004 17 55 59 > > >
A major stateside retailer Burlington
A major stateside retailer Burlington
Coat deploy large and many Oracle9i RAC
databases on x4XX Series clusters using
PolyServe. Here is a case study
http //www.polyserve.com/pdf/Intel-PS_BDaniele Bernazzi wrote
> The procedure I did use to build a sles8 on a compaq dl380 with
> controller smartarray 641 was
> - download cciss driver cpq_cciss_2.4.46-unitedlinux.dd.gz
> - unzipHello
I 'm sorry to bother the whole community with this topic but I hope the
mailing list mantainers are reading this thread.
Every time a mail is sent to the mailing list several undeliverable
Note 236826.1
"Supported and Recommended File System on Unbreakable Linux "
I quote "When choosing a file system performance is not the most
important point. "
An there under ext3 I can reaThank you Mike.
It 's good to know there is a solution out there! )
Fabrizio
> -----Original Message-----
> From Mike Tierney [mailto miket@(protected)]
> Sent 15 September 2004 23 45Hi
the gcc_old is for release 8.1 i tried to download but it won 't install. and orarun did not installl
i modified kernel setting by writing to sysctl.conf and then after booting running sysctl -phttp //rpmfind.net/linux/rpm2html/search.php?query gcc_old
> > > "Mohammad N. Tina " <mohammad_tina@(protected) > 09/11/04 11 49 AM > > >
Hi
I am trying to install oracle 8i on suse 8.2 i am following... seem to remember some question about making this work sometime back
(perhaps because I asked it!). OTN had instructions for an Oracle-enabled
PHP but with a standard Apache install not the Hi Glen
no there isn 't any orarun for 10g yet. We hopes for the future. You can
still use the one for SLES8 and 9i.
During DB creation you can encounter hugetlb issues (oracle unable to
allocaTwo things
I have heard anecdotally that loading the dev libraries for gnome can
provide
a solution however perform a full backup before doing anything on this
machine.
Additionally youAll you have to do is comment out the Linux line in certified versions.
Brian Macy
[GNC] Walter Reif wrote
> i deleted the following lines
>
> [Certified Versions]
> Linux redhat-2.1 Uhi martin
i asked suse support the same question.
10g and 10g rac will be certified in oktober. oracle will provide patches
for db and crs so they also run unter sles9.
regards
walter
p
On Tuesday September 07 2004 @ 10 26 PM Alaska Daylight Time Greg Wallace
wrote
> I just upgraded my operating system from SuSE 9.0 Professional to SuSE
>9.1 Professional. Now the ApachI would relink everything to see if that helps.
On Wed 2004-09-08 at 00 25 Greg Wallace wrote
> I just upgraded my operating system from SuSE 9.0 Professional to SuSE
> 9.1 Professional. I just upgraded my operating system from SuSE 9.0 Professional to SuSE
9.1 Professional. Now the Apache Server in my Oracle Enterprise 9.2.0.5.0
installation will no longer start up. I get tI 'm trying to stop the Enterprise Manager Console by issuing the command
${ORACLE_HOME}/bin/emctl stop dbconsole
Unfortunately the command fails to stop the EM Console. Here 's the
output I ge |
|
|
